| Info |
|---|
HOME supported version: 1.8 |
| Note |
Before proceeding, please make sure you have the latest FW for your Merging device:and above |
Prerequisites
A Merging Lawo HOME certified network interface or driver:
Horus
Hapi and Hapi MkII
Merging Anubis
Merging MAD (version 2.2.7 and above)
Update the firmware to our latest version available here.
https://www.merging.com/support/downloads
...
Supported products
Hapi MKI
Horus MKI
Hapi MKII
Anubis
MAD (needs license, get in touch with your Merging sales rapresentative)
Setup
Open MTDiscovery and locate your compatible device, right click on it, then select “Open advanced page”:
In the “HOME” tab, enter the IP:PORT of your Lawo HOME server (or server cluster), and click on “Enable”
| Info |
|---|
In case you want to specify a HOME cluster it will be enough separating each <ip>:<port> combination with “;” (e.g.: 169.254.200.100:4222;169.254.1.222:4223). |
Once Registered shows “everything ok” you’ll find your device in HOME Device tab
To disconnect your Merging device from Lawo HOME, you can uncheck the “Enable” checkbox
How to setup a source in HOME
To create one or more sources, click on your device, go to “Senders” tab, then click on “New Sender”, select the number of sources (Senders) your want to create, the number of channel per source and the source label
Once created, it’s possible to route physical inputs to the stream channels by clicking on “I/O Routing”, select the physical inputs and click on “Connect” setup the source
To setup more parameters of the source. please refer to the device “advanced page”
How to setup a sink in HOME
To create one or more sinks, click on your device, go to “Receivers” tab, then click on “New Receiver”, select the number of sinks (Receivers) your want to create, the number of channel per sink and the sink label
Before proceeding to sink routing, a stream has to be connected to the newly created sink. Go to “Stream routing” and connect the desired stream:
Once done, it’s possible to route the stream channels to physical outputs by clicking on “I/O Routing”, select the channels, and click on “Connect” setup the sink
To setup more parameters of the sink. please refer to the device “advanced page”
How to setup a internal routing in HOME
In the device tab of HOME there’s “I/O Routing” next to “Receivers” that allows to route inputs with outputs, not limited to IP->Physical or Physical->IP but also Physical->Physical (for ZMAN-based devices)
Known limitations
The flexibility of HOME UI may imply that certain operations are achievable in Merging devices. However, because HOME has a general-purpose design, certain actions are restricted due to the features or constraints of Merging devices.
It’s not possible to patch virtual inputs with virtual outputs in Anubis or Hapi MKII
In Horus/Hapi MKI, when setting up a source, it’s not possible to disconnect the input card (every source must always have an input)
In Horus/Hapi MKI, when setting up a source/sink, all the physical channels must belong to the same I/O card and be contiguous
In Horus/Hapi MKI internal routing is not supported in HOME, please make reference to Merging’s UI
(Setup → Routing)
Windows is not responding in time to IGMP queries so the switch removes Masscore from the Multicast Group. Due to Windows reaction time, you might have to extend your switch IGMP timings.
Pricing
Compatibility with Lawo Home is inclusive with the firmware of Merging’s hardware devices. There will be no extra charge.
For Lawo pricing, please get in touch with your Lawo dealer or SI.
Concerning MAD an option is required to unlock the Lawo Home compatibility, please refer to your local Merging dealer/distributor for the price.
Support
In case you wish to report some issues on the merging products concerning the compatibility, please contact support@merging.com
For specific Lawo products inquires, please get in touch with your Lawo sales rapresentative.