Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »





Merging Technologies ZMAN-based devices, Anubis, Hapi MKII, ZOEM, MT48.
Previous devices, Horus and Hapi cannot run in Dante Mode.


How to access the Advanced pages

  1. With the device IP address (Anubis / Hapi MKII / MT48)
    In your browser, enter the device IP address followed by /advanced/index.html
    E.g: 169.254.80.179/advanced/index.html
    The device IP address can be found on the device Network Settings and in Dante Controller Device View > Status Tab.
  2. Through MT Discovery :
    Right click on your Merging Dante ZMAN device and select Open Advanced.


Dante Controller

Sample rate and network configuration can also be accessed with Dante Controller.
Some settings (device latency, audio codec,....) can only be accessed with Dante Controller.


GENERAL SETTINGS

 

Device Name

  • This is the unique zeroconf device name.  Other devices see this device name.
    Device Name is case insensitive, 31 characters max, Unicode and non-roman characters are not supported.
    See Dante Documentation for details.
    Reboot is not required for the change to apply.  Equivalent to device Setup menu > Network > Device Name (Hapi)
  • Location : information text (64 characters max)

Audio Configuration 

  • Sample Rate : current sample rate (44100-48000- 88200-96000-176400-192000)
    This setting can be modified with Dante Controller.

Network

  • Redundant mode : Activate / deactivate Redundant mode - only applicable to Merging devices supporting such feature.
    A reboot is required for the change to apply.
    This setting can be modified with Dante Controller.

Interface 1-2

Note : depending on the device, only Interface 1 might be available.

  • Link : status
  • Name : information only - can't be modified
  • Type : defines the type of IP V4 address used (Zeroconf - DHCP - Static)
  • Address - NetMask - Gateway - DNS : only available if Type is set to Static.
    Reboot is required for changes to apply.
    Those settings can be modified with Dante Controller.


INS/OUTS

Allows to change the name of module's specific Inputs and / or Outputs. (when applicable)




I/O ROUTER

Allows to connect physical I/O and Internal device router.

  • Max 16 Channels per module : Shows the 16 first channels of modules (only applies to modules having more than 16 channels)


SYSTEM

Build Number

Current firmware version

Configuration file 

  • Download / Upload : Save / Load device configuration (preset file).

Commands

  • Shutdown : shutdown the device
  • Reboot : restart the device
  • Reboot to Factory : restore all settings to factory default, and restart the device
  • Restart : Restart the application (Mission)
  • Save : save the current configuration.

Debug

  • Get Report : generates a debug report, and saves it on the local computer. 
    If the report is not saved automatically, make sure your web browser did not block the download.
  • Get Device Status : displays the device status (SysLog)
  • Get Device Engine Status : displays the device engine - ZMAN-based devices only


UNIT IDENTIFIER

Identify me : Provides visual feedback on the unit to allow the user to quickly identify a unit (currently only available for ZMAN-based products; Anubis, Hapi MKII).
When ticking the checkbox :

      • Anubis and MT48 displays their Device Name on TFT and flashes Home button.
      • HapiMkII flashes its front panel Merging logo.


Appendix

  • Dante mode is only available for Merging Technologies Anubis and Hapi MKII, and Neumann MT 48.
    Previous Merging devices, Horus and Hapi, are not compatible.
  • Dante mode requires a Dante license (Dante Ready)


https://www.audinate.com/learning/technical-documentation
https://en.wikipedia.org/wiki/Precision_Time_Protocol








  • No labels