Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Next »

General Info.

This is in no case an exhaustive configuration procedure, It's a simple guide on how to configure these switches to use them with Ravenna/AES67 networks.

Before Starting

Important! If you have problems accessing the switch for configuration when connected to the Merging MassCore PCIe Ethernet card (NET-MSC-GBEX1) please connect it to the PC’s on-board Ethernet port. When configuration is completed reconnect the switch to the MassCore Ethernet card.

 

 

Cisco SG300 Switch  Auto-configuration Procedure

Note: For Cisco SG300 Switches other than the SG300-10 and SG300-20 please use the manual configuration procedure

 

  1. Right click on the Network icon in the Windows Taskbar.

  2. Select: Open Network and Sharing Center

  3. Click on: Change Adapter Settings on the left of the pane.
     

  4. Right-click the Merging Technologies PCIe 8257 RAVENNA Network Card and select Properties:
    (same procedure applies with any other network adapter)
     

  5. Select Internet Protocol Version 4 (TCP/IP) and Click on Properties:
     

  6. Click on the Use the following IP address: radio button and enter 192.168.1.2 (the Cisco SG300 switch has a factory default IP address of 192.168.1.254).
    Click on the OK button to accept the settings and close the dialog. 
     

  7. Open a browser and type 192.168.1.254 in the address bar, username: "cisco" password: "cisco", Click on the Log in button .

     

  8. After the login prompt, you will be asked to change that default password to whatever you want.
    It is a required step and the first one into securing you're router/switch, it is also a one time step only.

    After the default is changed, if you wish to change it again it you will have to do that in the Administration page.
    Reseting the switch to "factory defaults" that will also ask you to do this step again.

     

  9. The Administration page will now load and you cant start configuring your switch.
     

  10. Download the latest configuration file for your Cisco SG300 switch model :
    Cisco SG300-10
    Cisco SG300-20
    The Merging RAVENNA configuration file will auto-configure various settings /protocols to optimize the RAVENNA / AES67 network, and also sets the definitive fixed IP address of the switch: 169.254.252.1). 

  11. Go into "Administration" then click "File Management" to expand, then click "Download/Backup Configuration" to open its pane.

  12. In there in the "Save Action" click on "Download" (its chosen by default).
    Then on "Destination File Type" choose "STARTUP CONFIGURATION FILE"
    Then click on BROWSE and a new window will pop up.
      

  13. In the browse window, point to the downloaded configuration file  location, select it and click "open"
     

  14. Then click"Apply" for it to load your configuration file into the STARTUP CONFIG.
     

  15. Click "Done" to complete the procedure.

  16. tut
  17. The switch is now only accessible thru HTTP://169.254.1.254
  18. In the Network Connections window (see steps 4. 5. and 6. above), right-click the Merging Technologies PCIe 8257 RAVENNA Network Card and select Properties.
    Select the Obtain an IP address automatically radio button and also select Obtain DNS server address automatically, click on OK.
     
  19. The switch is now configured and ready to use, and the Merging RAVENNA Network Card should have auto-configured itself with an IP in the 169.254.x.x range. 
    You can verify this by opening a browser and typing 169.254.1.254 in the address bar, Log in (username: admin password: admin).

 

  • No labels