Page Comparison

...

1. In the Getting Started page, click on Create VLAN.
   
   
   
2. Click on the Add button at the bottom of the VLAN Table.
   
   
   
   
3. Set the VLAN ID: 2  and enter a VLAN NAME (can be anything you want, please do not use special characters).
   Make sure VLAN Interface Status and Link Status SNMP Traps are both active.
   Click on Apply once done.
   
   
   
   
4. Go to VLAN Management >  PORT TO VLAN, 
   In the Filter section, set the VLAN ID to 2, and Interface Type to Port.
   Click on Go.
   
   
   
5. Now you can see that all ports for VLAN 2 are excluded, you need to assign the required ports to this RAVENNA/AES67 VLAN.
   Set the required ports from Excluded to Untagged Untagged (in the picture below, ports 5 to 8 and port 10 are assigned to VLAN 2.
   Click on Apply once done.
   
   
   
   
   
6. You may now check your VLAN1 config. 
   In the Filter section, set the VLAN ID to 1, and Interface Type to Port.
   Click on Go.
   You can see that the ports you have added to VLAN 2 are excluded from VLAN 1.
   
   
   

7. This explains how to change ip for VLAN2 so the admin page of the switch can also be reached from VLAN2
   

    

   Go to "Administration" then click "Management Interface" and then "IPV4 Interface", the following pane will open in the right.
   Image Modified

8. In Management VLAN choose 2 and on IP Adress type in the IP Adress you want.
   I suggest you use the settings as shown in the picture bellow.

   Info
   title Note
   For VLAN2 appear on "Management VLAN" you will have to have something connected to it (at least one port in USE).

   Image Modified

   Save your settings, and reboot the device.

9.  

   Here is how to change the IGMP settings to use for VLAN2 Ravenna AES67.

    

   Click on "MULTICAST" on the left menu.
   Image Removed
   Click on "IPV4 Multicast Configuration" and then click on "IGMP SNOOPING".
   Image Removed
   The following pane should show up in the right side.
   Make sure "IGMP SNOOPING STATUS"  & "IGMP QUERIER STATUS" are ticked "ENABLE" as show in the picture.
   Image Removed
   Select the "ENTRY 2" (vlan id 2) and click on "EDIT" as shown on the picture below.
   Image Removed
   In the window that just popped up edit the entries there (all the yellow marked entries, should be set as shown) and click "APPLY"
   Image Removed
   Click on Copy/Save Configuration link (yellow marked) to go save your configuration .
   Image Removed
   Choose "Running Configuration" and "Startup Configuration" and click "Apply".
   Image RemovedClick on "DONE" button and that is it.
   Image Removed
   

    

   On the left pane menu, click on MULTICAST.
10. Then click on IPV4 Multicast Configuration to expand it.
    Click now on IGMP SNOOPING.
    
    Image Added
11. In the IGMP Snooping page, enable both the IGMP Snooping Status and IGMP Querier Status checkboxes.
    Then click on on Apply.
    
    Image Added
    
    
12. On the IGMP Snooping Table, click on the radio button next to VLAN 2 to select and then click on Edit.
    
    Image Added
    
    
13. Configure the IGMP Snooping Settings as on the picture below, and click Apply once done.
    
    Image Added
    
    
    

14. By default, Green Ethernet settings are applied, this needs to be disabled.
    Please check your current configuration and set them to the same as show in this guide.
    browse to Port Management > Green Ethernet > Properties
    Untick both Energy Detect Mode and Short Reach

    .   
    Untick 

    , and untick 802.3 Energy Efficient Ethernet (IEEE)

    
    Image Removed
    

     

    By default, our config files use the Basic QoS Mode but the DSCP to Queue are settings modified.
    Please check your current configuration and set them to the same as show in this guide.
    QoS Mode: Basic MODE
    Image Removed  Image Removed
    On the QoS Basic Mode / Global settings the Trust Mode should be : DSCP
    Image Removed
    
15. By default these are the DSCP to Queue settings, we will change that.
    Image Removed
Change the DSCP to Queue Settings as

 as well.
Click on Apply once done.
Image Added




16. Browse now to Quality of Service > General > QoS Properties.
    The QoS Mode should be set to Basic.
    Click on Apply
    Image Added
    
    

17. Go now in Quality of Service > QoS Basic Mode > Global settings.
    The Trust Mode should be set to DSCP
    Click on Apply.
    Image Added
    
    
18. Go back to Quality of Service > General, then DSCP to Queue.
    Change the DSCP to Queue Settings as shown in the following picture and click apply to apply the new settings to the current running configuration :
    Image RemovedOnce you click apply the following appears at the top of the DSCP to Queue window.
    Image Removed
    Click on the Copy/Save Configuration link to go directly to the save configuration page.
    Save your settings from Running Configuration to Startup Configuration (click apply to save).
    Image Removed
    That will then Apply  once done.
    Image Added
    
    Note : Queue 34 : RTP AES67 / Queue 46 : PTP AES67 / RTP Ravenna / Queue 48 : PTP Ravenna / Queue 56 : PTP Dante
    
    

19. Now is a good time to save the configuration.
    Go in Administration > File Management > File Operations.
    Select Duplicate as Operation Type.
    Source File Name : Running Configuration
    Destination File Name : Startup Configuration
    Click on Apply
    
    Image Added
    
    This will apply the current settings to the start up configuration

    witch will be run every time the switch reboots

    .
    In other terms that makes that configuration to

    become permanent

    be permanent (unless a reset of the device is done).